How to Remove and also Replace a Bathtub.
How to Remove and also Replace a Bathtub.
Blog Article
They are making a number of good points on the subject of How to Install a Bathtub Yourself overall in this content directly below.
Installing a bathtub isn't precisely rocket science, however it does call for strong plumbing, carpentry, and sometimes, tiling abilities. Replacing an old tub with a brand-new one is also a moderately tough task. If the old tub is easily obtainable, the project can move immediately; if you need to open a wall to eliminate the old bathtub and also position the new tub, the job is a lot harder. In either case, the job is within a house handyman's abilities, although you will certainly need a helper to leave the old tub as well as embeded in the brand-new one. Make sure you have qualified on your own for the work and also fit attempting it. Rather than hiring a contractor to take over a halfway-completed project, it is better to consider employing one before you begin. Chances are you might require an expert plumber to make tube links.
This post will certainly aid you install a new bathtub in your bathroom if you have currently bought a new tub and do not require to transform the setup of your previous water supply pipes.
Your devices and also product list need to consist of the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The procedure of getting rid of the existing taps can be quite problematic as a result of the limited accessibility that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will come from the pipes. When the supply pipes have actually been removed, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from turning throughout this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old sealing substance.
Before proceeding to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the connector fits on the plastic tail of the tap and also the other end offers a link to the current supply pipes.
If you require to fit a monobloc, then you will call for reducing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the faucet in the placing hole in the bath/basin ensuring that the washing machines are in location in between the tap and also the sink. Protect the tap in position with the manufacturer provided backnut. As soon as the tap is securely in position, the supply pipelines can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical tap adapters. The former kind ought to be attached to the tap finishes first, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bath tub
Using both wood boards under its feet, place the tub in the called for position. The wood boards are helpful in uniformly spreading out the weight of the tub over the location of the boards instead of focusing all the weight onto four little factors.
The next objective is to make certain that the bath tub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the tub up until the level reviews level.
To install taps, fit the bottom of the outermost adaptable faucet adapter to the ideal supply pipeline by making a compression join; after that do the same for the various other tap.
Turn on the water and also check all joints and new pipework for leakages as well as tighten them if essential. Fill the bathtub and also inspect the overflow outlet as well as the typical electrical outlet for leakages.
Finally, fix the bath paneling as explained in the maker's instruction manual. Tiling as well as securing around the bath tub needs to wait until the bath tub has actually been made use of a minimum of when as this will settle it into its final position.
Preparing for the Installment
To start with, the sustaining structure provided with the bathroom needs to be fitted (if called for) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets system to prevent stress on the tub.
Fit the flexible faucet connectors to the bottom of the two taps making use of 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you utilize all of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be suited its last placement.
Tiling Around the Bathtub
In the location where the bathroom meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to fracture a stiff seal, causing the water to permeate the wall in between the bath and also the tiling, resulting in complications with wetness and possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your components and installations. They are offered in tubes and also cartridges, as well as are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to always fill up the bathtub with water prior to sealing, to enable the movement experienced when the tub remains in use. The sealer can fracture fairly very early if you do not consider this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise conveniently available on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were brought to that editorial about A Step-by-Step Guide to Installing a Bathtub through a friend on our other web property. Do you know somebody else who is in the market for the topic? Please feel free to share it. We thank you for reading our article about Installing A Bathtub.
Additional Information Report this page